Fixtures, lines and hookups set the right way
Plumbing installation in Brigham City, UT is the work of putting in new water, drain, vent and gas connections, or hooking a fixture or appliance to the ones you already have. It is different from repair, where something that worked has stopped.
Most calls we hear fall into a few groups: a new shower or tub, a sink or toilet swap during a remodel, a washer or dryer hookup, and a property that has no plumbing run to a building yet.
Smell gas? Leave first, then make the calls
If you smell gas, do not look for the source and do not flip a switch, light anything or use a phone inside. Leave the building right away and take everyone with you.
- Get outside and move away from the house.
- From a safe distance, call 911 or the gas utility. Enbridge Gas Utah lists a 24-hour emergency line at 1-800-767-1689.
- Stay out until the gas utility or fire department says it is safe.
- Call a plumber only after that, for repairs or a new gas line inspection.
We cannot promise how fast anyone arrives, and a plumber is never the first call for a gas smell. The utility and emergency crews have the meters and detectors for that moment.
What we install
Toilets and sinks
New bowls, vanities, kitchen sinks and the shutoff valves and supply lines under them.
Showers, tubs and jetted tubs
Valves, drains and trim, plus the rough-in for a new bathroom.
Laundry and appliance hookups
Washer boxes, drain standpipes, dishwasher and fridge water lines.
Gas piping
Appliance hookups such as a range or outdoor grill, plus inspection of existing lines.
New construction rough-in
Supply, drain and vent runs set before walls close.
Remodel changes
Moving a sink, adding a bathroom or trading a tub for a walk-in shower.
If a toilet is the only thing giving trouble, see toilet repair before you buy a new one. A new tank heater is covered on the water heater installation page.
Remodel on the way?
Share your fixture list and floor plan details, and we will tell you what the rough-in needs.
Planned installs versus jobs that need a repair first
| What you want | Check before we start | Why it matters |
|---|---|---|
| New toilet in the same spot | Shutoff valve and flange condition | A corroded flange or stuck valve changes the job. |
| Swap a kitchen or bath faucet | Hole count, valve age, supply line length | Old supply valves often fail when moved. |
| Shower valve replacement | Access behind the wall, pipe material | May need an opening in tile or drywall. |
| Washer or dryer hookup | Drain height, venting, gas or electric | A drain too low or a missing vent causes backups. |
| Add a bathroom | Where drains and vents run nearby | Slope and vent distance limit where fixtures can go. |
| Gas appliance hookup | Gas line size and shutoff location | An undersized line starves the appliance. |
A fixture that keeps leaking is sometimes better served by faucet repair than a full replacement.
Planning a remodel or new build in sensible order
- Decide fixture locations
Pick sinks, toilets and tubs before framing, since drains and vents depend on where they sit.
- Rough-in
Supply, drain and vent runs go in while walls and floors are still open.
- Inspection
Rough-in work is usually inspected before walls close. Ask the building office what your job needs.
- Set fixtures
After finishes go on, fixtures are set, connected and tested for leaks.
- Final check
We run every fixture, check traps and shutoffs, and show you where the valves are.
Decide early, because moving a drain after the slab or floor is closed costs far more than moving it on paper.
Gas line work, once the area is safe
Calls about gas piping usually involve a stove or grill hookup, a rusty-looking line, an office or renovation that needs a new run, or a request for a clearance check after a utility visit. Some callers only want a price for an inspection.
Planned gas work starts with sizing: a run must carry enough gas for every appliance on it. We check pipe size, shutoff locations and the condition of fittings, then pressure test before anything is lit. Gas is not a place for a homeowner to experiment, and the gas utility handles anything on its side of the meter.
When a plumber is not the right call
A hot tub or jetted tub needs a dedicated electrical circuit, and wiring is an electrician's work, not ours. We handle the water and drain side.
Structural cuts through joists or foundations are a carpenter's or contractor's decision. Meter-side problems belong to Public Works at (435) 734-6615.
What shapes the price of an installation
Distance to existing lines
A fixture beside current pipes costs less than one across the house.
Fixture type
A basic toilet is simple, a body-spray shower or jetted tub is not.
Access
Open framing is quick. Finished walls or a slab add labor.
Pipe condition
Tired supply lines or valves sometimes need replacing at the same visit.
Permits and inspections
Some jobs need them, and fees and timing depend on the city.
Homeowners insurance generally covers sudden accidental water damage, not a new installation or an upgrade. Ask your agent if a failure caused the work. If supply lines behind the walls are the weak link, repiping may make more sense than a new fixture on old pipe.
Want your real number? Call (855) 575-2890 for a clear price before work starts.
Permits, licensing and the city's backflow guidance
Permit rules vary, so ask the Brigham City building office at (435) 734-6604 before starting. The office is at 20 N. Main, 2nd Floor. Utah adopts plumbing codes through the state, so ask which edition applies to your job.
The city publishes guidance on cross-connection control and backflow prevention. If your installation adds an irrigation hookup or a new outdoor spigot, ask Public Works what applies. You can also confirm any plumber's license class on the Utah Division of Professional Licensing Verify a License tool.
Homes in Willard, about 7 miles south, follow the same steps, and you should ask Willard City whether your address is on city sewer before planning a new drain.
Frequently Asked Questions
Leave the building first. Once you are safely away, call 911 or Enbridge Gas Utah at 1-800-767-1689. Do not call a plumber until the utility says the area is safe.
Often yes, but we look at the fixture and the connections before agreeing. Missing parts or a mismatched valve can change the job, so tell us the model when you call.
Usually, depending on where nearby drains and vents run. The key limits are drain slope and vent distance, which we check before quoting.
Permit rules vary, so ask the Brigham City building office at (435) 734-6604 before starting. Simple fixture swaps and new rough-in can be treated differently.
We can inspect and size gas piping and connect appliances. If you smell gas at any point, leave and call 911 or the gas utility first.
Not usually. Policies often cover sudden accidental water damage, but not upgrades, wear or the new part itself. Check with your agent.
Use the Utah Division of Professional Licensing Verify a License tool. It lists apprentice, journeyman, residential journeyman, master and residential master classes.
Sources and standards
- Plumbing codes in the UPC and IPC families set the rules for fixtures, venting and drains. Ask the Brigham City building office at (435) 734-6604 which edition and permit rules apply to your job.
- The Utah Division of Professional Licensing offers a public Verify a License tool for checking any plumber's license class.
- The Brigham City Water Division explains hardness, pressure testing and water quality on its water page. Call Public Works at (435) 734-6615 with questions.
- Blue Stakes of Utah asks you to call 811 at least 3 business days before any digging so buried lines get marked.
- Enbridge Gas Utah says to leave the building first if you smell gas, then call 911 or its 24-hour emergency line from outside.
Written by Brigham City Pro Plumbing. Last updated October 29, 2026.